Author: Forum News

Hey guys

I just bought my Dad's 1999 xplorer 400. It has 1600 miles on it. My Dad never tinkered with it at all. It still has everything stock and setup for sea level. That would be fine if we didn't live at 6000ft lol. I'm looking to get a good clutch kit for 6000-9000'. I installed a tach and the most RPM I have seen is 3020. I know the belt needs changed and most likely the jetting. Any suggestions on a clutch kit or setup would be great!

Thanks

Has any one done ceramic coating on their y pipe back to the muffler on a outy 1000 to keep heat down. Mine is the 6x6 but all the engines n y pipes are the same

I have a 2018 XMR 850 and the plastic bracket that holds the shifting linkage in place broke off on me . Is there an easy way to change this out ? Anyone else experience this ?

Hey everyone I bought a 2000 Polaris Sportsman 500 and it's got factory wheels on it. I want to get a new set of tires for it but the Polaris shop told me the front should be 25x8x12 and the rear should be 25x10x12

The rears that are on there right now are 25 x11x12 so I'm a little confused and don't want to order the wrong tires.

Can someone tell me what actual size should be?

Up North Technologies just added a new hardware kit (longer fasteners and spacers) to use their front or rear mount ATV-1 LINQ Adapter with a front or rear rack. Previous lower spacers would not clear the base of the racks with the ATV-1 adapter kit.

I am a big fan of Kens products and customer service since adding a Pro Series rack on my 2016 BC X camp/play sled a couple of years ago. OEM fit and finish and great customer service.

The ATV-1 adapter for not everybody but if you do high mile day trips its nice to have spare fuel handy and I can even mount my Sled Solutions Elevation gear bag too if extra storage is needed instead of fuel. Pretty sweet system to share LINQ options between my sled and ATV. He sent me a updated longer spacer kit n/c after I bought the ATV-1.
Thanks Ken!

Attached Images

File Type: jpg	DSCN2266.JPG (1.87 MB)
File Type: jpg	DSCN2264.JPG (1.59 MB)
File Type: jpg	DSCN2265.JPG (1.75 MB)
File Type: jpg	DSCN2260.JPG (1.62 MB)
File Type: jpg	DSCN2079.JPG (1.84 MB)

I just updated my XP1000 PIDD to the latest software from RideCommand (Dated 9/20) and it totally broke my display. Boots up and everything, but then after a few seconds it comes up with a message saying "UNABLE TO CONFIGURE PLEASE SEE DEALER", blocking more than half the screen, making it almost completely unusable. Planning on a huge trip tomorrow, and now I'm screwed.

Anyone happen to have a PIDD update for the 4.3 screen prior to 9/20? You can't download older versions off the RideCommand site, and wouldn't it figure that I had an old version on my USB stick, and of course I overwrote it.

Here's a video I took to send to RideCommand:
Not sure what else to do to get it working for tomorrow's ride. Ugh...

Anyone know where to get a service manual for a 2017 xmr that is not a DVD. A actual paper manual that I can get greasy finger prints, and spill beer on. I don't have a laptop to put in the garage, any help, much appreciated.

Hey fellas,

What's the ETA on these plates??

Thanks in advance,

Kevin

New to forum. Trigger coil shows open when tested with ohmmeter. Looks easy enough to get to but the wires run behind flywheel. Do I need to pull the flywheel to replace it or is there a trick I need to know?
Thanks