Author: Forum News

Hi everyone.. I got a 2010 Sportsman 550XP EFI and Im getting a trouble code of 520193-7 which Im told is the IAC circuit. I checked for bare/broken wires and tested the IAC with ohm meter and all checked out good. I am also having an issue with starting the bike, single click and nothing else, if I use a screwdriver across the solenoid itll start, and also sometimes just immeadiately shuting off, usually after romping on it a little and then letting off, it's like all power is taken away NOW. Shuts off very very quickly. Has anyone ran into the issue/code and does anyone know if a bad battery would create these issues, including the IAC code.

P.S. It's the original battery in bike..

Thanks in advance,

Bob

I recently purchased a 2002 Polaris Xplorer 250 4x4. It does not start and I have been trying to get it to start. Everything electrical is working great and I have a good spark. Also, fuel is being delivered and I took the carb out and cleaned it well. Today I did a compression test and only turned up 30 psi and I know this is way too low. And its not my gauge because I tested the gauge on my lawnmower and it turned up over 100. I took the valve cover off and the head gasket seems to be OK. I just can't figure out where I am losing compression and what the best way would be to get enough compression to start it up. Any help or recommendations are greatly appreciated.

I recently purchased a 2002 Polaris Xplorer 250 4x4. It does not start and I have been trying to get it to start. Everything electrical is working great and I have a good spark. Also, fuel is being delivered and I took the carb out and cleaned it well. Today I did a compression test and only turned up 30 psi and I know this is way too low. And its not my gauge because I tested the gauge on my lawnmower and it turned up over 100. I took the valve cover off and the head gasket seems to be OK. I just can't figure out where I am losing compression and what the best way would be to get enough compression to start it up. Any help or recommendations are greatly appreciated.

Long story short...my girlfriend put her 99 scrambler 400 4x4 into a puddle (pond) today. We towed it home and pulled off the filter, carb, air tube on the lower left side and spark plug. We turned it over a bunch to get some water out but not sure where to go from here. I'm mechanically inclind and will be trying to get it going my self but I know nothing about 2 strokes. Motorcycles and cars yes. Need detailed help. More info the better.
Thanks in advance
BTW new to quading...the both of us and have really been enjoying it. Except today!!

Hello all, new member here from upstate NY. Just traded my sportsman 850 for an outlander max 850 xt and couldn't be happier!

My project is getting newer one part at a time. I need to replace the lower steering bushing and hope someone can give me some tips. Does anyone know what needs to be done to remove the old bushing and install the new one? There is a large bolt at the bottom of the steering shaft that will need to be removed. Once that is loose will the steering shaft slide up a few inches to replace the bushing? I appreciate any info that will keep me from wasting time. Thanks.

Hello everybody, I am just sending this out there to see if anyone has done any mods to the muffler on the new sportsman 1000. I am not sure if the muffler on the sportsman is a catalytic muffler like the RZR, and if so has anybody gutted it??? I have gutted a RZR turbo muffler and I noticed a pretty fair increase in power. I would like to know if anyone has done it before I do it:devil

Does anyone have a 325 or 330 cylinder head off their machine? I have my MOSE with the 330 engine that I can't get to run right. I am afraid I put the 325 head on it rather than the 330 head. There isn't a part number stamped into the casting.

All I can find is a few markings on the bottom side. They are different but I can't tell from them what the head is supposed to go on. From the measurement that I have tried, it appears that the combustion chamber is different between them. I don't have the tools to correctly cc the chamber so I am trying to figure it out another way. Any help would be appreciated!

I have a 04 sportsman 500 HO that won't start. The battery is new. It won't do anything. I can pull cord start it that's it. After getting it running by pull starting it, lights, winch, instrument cluster won't work. Thanks in advance