Author: Forum News

Hey guys I got some hd5 beadlocks with 27x11x14 and 27x9x14 tires that I bought a month ago for sale and they have 6 miles on them in brand new condition and they were just to agressive for my liking so I'm selling them for 1000 including shipping I paid 1300 for them and they are 4/156 pattern they fit sportsman atv and sxs etc

Good morning. I need some advice. My 2005 sportsman 400 won't start. I turned the key as to start it and with out the engine turning over I hear a loud bang. It sounded electrical especially since nothing from engine turned. If I pull start it, it will only start once and it will run for a few seconds and die. Then it wont pull start till many hours later and it will do the same, start and not run more than a Second or 2.
What's the possibility it could be the selonoid or related? Any advice would be a great help ty
Steve

I bought an unknown year tb 250 lower on ebay and the inner seal on the old one (98) had a retainer ring with screw holes in the block to hold it on. the new one has no such holes. can anyone one help me figure out the year and or how i can secure it? Picture is of the new lower. Thanks in advance!

Attached Thumbnails

 

Let the voting begin for the June 2017 Polaris ATV of the Month! We will leave the poll open until the end of the month and then announce the winner. We got some really good pics this month, thanks to everyone that participated and GOOD LUCK!!

andwes03



2015 Sportsman 570
QSC Clutch Kit
Kenda Bear Claw HTR's
Viking front brushguard
12 LED light bar
Custom LED flush mount headlights
Heated handgrips and thumb warmer
Polaris Rear Tough Rack
Modified Polaris Lock and Ride rear storage box
2 LED pods mounted to rear rack for reverse lights
2500lb Polaris Winch
Warn Provantage Snow Plow
Cecco racing billet aluminum thumb throttle lever

TheStatelineATV



2009 xp 850 with tons of upgrades

bobx2

2015 Sportsman 570 Touring EPS
26" Kenda Bearclaw HTR's on ITP Delta Steel wheels
Warn XT25
Iron Baltic HDPE Skid Plates

Bshuk57



2015 Scrambler 850.
28" Sedona ripsaws on ITP SS212s
Full Ricochet aluminum skid plates
Custom 3rd headlight
Dry storage box
To-do list includes
RVS reflash
Rick Cecco frame braces
QSC clutch kit

BlueFire570SP



2015 Sportsman 570 SP Touring

1948boat



2003 Polaris Trail Boss
STOCK,
new chain and sprockets
new Polaris belt
new rear break pads
all lubes and filter changed

bp405



05Dirtymax



2005 sportsman 700 EFI twin
26" super swamper vampires
LED bars mounted in factory headlight location

Hi

I have a 2012 sportsman 550 EPS & I'm going to change the rear wheel bearings.

Can anyone tell me how many ft lbs to torque the castle nut too?

I found some you tube videos but they all had different torque specs & none of the videos were for my specific model.

Thanks in advance

Any help or opinions are greatly appreciated, I have a 2008 Sportsman 800 with 1200 miles of light use, I have owned since new. Due to a 4wd problem (constantly locked in) I took out my front differential hoping to find the common blown up sprague cage, well that I did not. Every thing appears to be in great condition and intact other than when I took out the output pistons and parts on the drivers side I found wrapped around the output pistons was a bunch of black plastic material. It appears the piston was rubbing against the black plastic ring section (see pic 1 zoom in) that comes as part of the case on both sides. I assume it is some type of a coil or something? Not sure if this is supposed to be ever touching or not. It almost seems like in a manual transmission you have the flywheel and pressure plate that might be slipping causing it to melt off instead of making full contact? Just not sure how these 2 parts are supposed to mate or not touch at all. I assume the 4wd is locked in because of the mess that I found(see pic 3). If you look at the second pic(zoom in) I also have 2 pretty good grooves worn in the armature piece not sure if this is supposed to happen either? I posted a few pics first should show the wear/melting on the whatever its called, second shows the mess on the workbench and third shows the melted pieces that are from the first pic. The passenger side does also have some wear on it but no real debris. Thanks to all who can help and hope I put this in the right section. If not please advise.

Attached Thumbnails

     

Just bought a 2015 850. Ran great first day but when I started out the next day the engine began hesitating when I throttled. Played around with it for half an hour and it ran great the rest of the day. Two days later I hopped on and it did the same thing. It idles fine, but when I give it gas it dies. I try to keep out of heat but it didn't help