Posted on

Good place to buy a slightly used ATV?

Hey everyone.

I am trying to find my first Can-am to purchase, but it is proving to be harder than I originally thought to find something to spend my money on. haha. Not the usual problem.

I am looking in that range of a year to a few years old, with low miles/taken care of. I don't want to pay brand new price when I am fine with slightly used. Looking for a Renegade XXC or XMR 1000. I can't even come close to finding something on CL or eBay. Are there certain places I should be looking? My dealer only has one used ATV currently, and they're the only dealer for 100 miles.

Any help would be appreciated!
Posted on

2015 850 Touring transmission

New owner of 2015 850 sp touring with 600 miles. I’ve gone through most of the machine (all fluids, air filter, chassis lube ) to get ready to ride, but have a question about drive engagement. When sitting still, the machine clunks (especially in reverse) when the transmission engages. Seems ok while moving but the clunk engagement from stand still seems harder than I would expect. Anyone have insight???
Posted on

Xploer 500

I bought a xplorer 500 and the tires and rims are shot the bike had 25-8-12 and 25-11-10 on it my my question is can I use 25-8-12 and 25-10-12 from a 13 sportsman please be gental I’m a noob
Posted on

Indian Ridge partially closed?

I see on the HMT website that Indian Ridge is closed across the street from Ashland.

Bob T updated his map files late 2018 to show its been reopened.

Does anyone know whats really going on here?

Sent from my SM-G930V using Tapatalk
Posted on

Code 520207-4

Atv started reading this code and would not turn over while code is there. It is an intermittent code so when it goes away it will crank and run fine but when code pops back up while running I don’t have awd or no lights work. I know it says it’s an awd circuit grounded but where to start? Help!!
Posted on

96 sportsman hub seal question

I replaced the right hub seal due to a leak.The hub seal sleeve had a significant grove in it, but I took a chance it might work. The leak is still there but not near as bad. Has anyone use the ready sleeves to repair this issue? The cost is about the same to replace the hub sleeve or or use the ready sleeve.My biggest concern is damaging the coil during removal of the hub seal sleeve. Or while driving the ready sleeve over the hub seal sleeve and pushing the hub seal sleeve to far inward(out of spec) and not being able to reposhining it. The ready sleeve number for this application id 99262.
Posted on

Valve Cover Gasket Failure Help

Hi everyone! I just recently purchased a 2007 Renegade 800 with 112 hours and 1024 miles. I did a rad relocate, 30 inch silverbacks, cvtech primary, stm secondary, and a few other mods to go along with those. I've recently ran into an oil leak issue that I cant seem to beat. I've never experienced a leak this bad. Both valve cover gaskets were spewing oil out of them while riding so I replaced the valve covers and gaskets with new can am parts from my local dealership. Today I did that job and the original valve covers were warped so I assumed that was my issue. After installing the new covers and gaskets I torqued everything to 62 in-lb as I've read to do on another thread. I let it idle up to running temp and it seemed perfect. No leaks at all and it sounded great. So I took it down the street a couple times not doing anything crazy on it just cruising and I park it in the garage and it was shooting oil out from both covers again! After some looking around it looked like both gaskets had been pushed out from covers and oil was shooting out from those spots. Again I never got on the throttle hard at all while on the test ride. So has anyone else had this happen and come up with a solution? Or could you tell me what I did wrong😂 all help will be greatly appreciated!

Attached Images
File Type: jpg 20190311_153032_1552337867866.jpg (4.79 MB)
File Type: jpg 20190311_153015_1552337944217.jpg (1.35 MB)