2003 Sportsman 700. I have ordered 3 different brands of rear axle, including an OEM. All the correct part #. Rear/Left side. Splines stick out about 3/4" beyond where they should. Am I missing something? Any help would be appreciated.
In-Filter Breather
Hi everyone,
Relatively new to ATVs and I perhaps have a stupid question, but I was curious anyway.
The 2008 Sportsman 500 is currently on jack stands, in pieces as we repair a few things with the front end differential. Not related, but we noticed what looked like a filter on the left hand side under the panel. Upon further investigations, I determined it was an in-line breather filter.
What does it do? I notice it goes into the airbox. Is this something I should be replacing on a regular basis? The part is cheap and I figured while we have changed pretty much everything else maintenance wise I would check on this before we begin putting it back together again.
Thanks guys & gals.
Relatively new to ATVs and I perhaps have a stupid question, but I was curious anyway.
The 2008 Sportsman 500 is currently on jack stands, in pieces as we repair a few things with the front end differential. Not related, but we noticed what looked like a filter on the left hand side under the panel. Upon further investigations, I determined it was an in-line breather filter.
What does it do? I notice it goes into the airbox. Is this something I should be replacing on a regular basis? The part is cheap and I figured while we have changed pretty much everything else maintenance wise I would check on this before we begin putting it back together again.
Thanks guys & gals.
Reversed batter terminals with new battery
Hello,
i am new to this forum and I would appreciate any help from any of you!
I have a 2014 Sportsman 400 HO. Last night I went to get my ATV blade on to get ready for some snow. The battery was dead so i jump started it and it ran fine but the battery wouldn't hold a charge so i bought a new battery. I had my son install it but nothing worked. When i inspected it I realized that he hooked the battery up backwards. I hooked the battery up correctly and now it wont start. It turns over fine and the lights and winch works. I checked the fuses and all 4 of the were good. My question is where would someone recommend that i start with replacement parts? Any help would be much appreciated.
Thanks
i am new to this forum and I would appreciate any help from any of you!
I have a 2014 Sportsman 400 HO. Last night I went to get my ATV blade on to get ready for some snow. The battery was dead so i jump started it and it ran fine but the battery wouldn't hold a charge so i bought a new battery. I had my son install it but nothing worked. When i inspected it I realized that he hooked the battery up backwards. I hooked the battery up correctly and now it wont start. It turns over fine and the lights and winch works. I checked the fuses and all 4 of the were good. My question is where would someone recommend that i start with replacement parts? Any help would be much appreciated.
Thanks
Lighting
I purchased a 2002 325 Magnum for my wife and noticed a problem with the lights. It had no brake light so I checked the bulb,sure enough,the filament for the brake light was broken. No problem,new bulb,right? Wrong...put a new bulb in now the brake light works,but it also comes on with the head/tail lights. I suspect the bad bulb was put in intentionally. Without pulling everything apart to troubleshoot the harness I just wondered if anyone else has had this happen just to save some time and trouble. Thanks!
Another newbie
Hello all. Been riding for years. Started on a Polaris Magnum 425 and have slowly upgraded. Been searching for the last few months on a new ride and it was between a brute force and the can am. Well we can all guess who won....... Picked up a new 2018 Outlander Dps 850 in orange. So far I am in love with it. Now with that being said. I am after some mods already for it. Mainly clutching and a upgraded belt. I have tried to search but have not found anything im 100% on with this being so new. Picture i have uploaded is the machine itself. Don't have any on my phone yet.
Polaris 400 cooling system
So I am replacing the Head Gasket on my sons 400 Scrambler - Along with the fan sensor (cylinder head) and the radiator sensor (both were new old stock) - After everything is reassembled is there a way to check the fan operation ? Can one of the sensors be jumped to turn the fan on ?
2017 Defender HD8 XT Cab fuel millage?
I was wondering what kind of fuel millage others are getting? I just picked up a great deal on a 17 Defender HD8 XT Cab and went on a 35.7 mile trail ride (Elk Hunting) and used 3.44 gallons that is 10.37 miles to the gallon. Now I did all this in work mode only with a average of 8 miles per hour. My next trip will be in Normal mode to see if any difference. Then third trip in Econ mode to see the difference. I was very happy with the performance and comfort of my Defender on this trip and looking forward to my next trip. I have been a side by Side owner since 2006 (Yamaha Rhino). Back to my question, What kind of fuel millage are other Defender owners getting? I just thought it would be higher.
Installed Rad Relocate
Just finished installing my Can Am rad relocate.
I found it to be a fair bit of work. I took off the plastics, which I probably didn't have to. That was the biggest part of the job. Getting those buggers on an off.
I guess the only other reason I found it a lot of work was because Can Am's instructions I downloaded were useless.
I purchased proper hose clamps, and did not use the one time use clamps that were provided. Just incase I needed to take a hose off (for future mods, or a mistake when installing etc)
I didn't mount the Can Am symbol on top of the rad. I was thinking of designing my own and cutting it out (I have a CNC Router that will do the job) Just not sure what I want on it yet.
This is my youtube video, if anyone is having thoughts of installing one, it may help ..it may not help!
https://youtu.be/YWKkWXsf5Io
PS Stay tuned for my Can Am plow I purchased on FB Market place :big-grin
I found it to be a fair bit of work. I took off the plastics, which I probably didn't have to. That was the biggest part of the job. Getting those buggers on an off.
I guess the only other reason I found it a lot of work was because Can Am's instructions I downloaded were useless.
I purchased proper hose clamps, and did not use the one time use clamps that were provided. Just incase I needed to take a hose off (for future mods, or a mistake when installing etc)
I didn't mount the Can Am symbol on top of the rad. I was thinking of designing my own and cutting it out (I have a CNC Router that will do the job) Just not sure what I want on it yet.
This is my youtube video, if anyone is having thoughts of installing one, it may help ..it may not help!
https://youtu.be/YWKkWXsf5Io
PS Stay tuned for my Can Am plow I purchased on FB Market place :big-grin
Glad to be here
Hello everyone. My name is Dexter skinner. I’m new to this forum.
I’m a retired Engineer that lives in both Florida and Costa Rica.
I resently acquired (4 month ago) a 2008 Can Am renegade to enjoy the true beauty of Costa Rica beach side life style. It’s been a dream to have one of these beast.
With the purchase of this unit, I have been spending a lot of my time bringing it up to excellent conditions. So far, things are going extremely well. Spending a lot of money on new parts with my travels back to the USA.
Once in a while I may ask for your help. Please be patient with me.
Thanks in advance for your help.
Regards: Dexter
I’m a retired Engineer that lives in both Florida and Costa Rica.
I resently acquired (4 month ago) a 2008 Can Am renegade to enjoy the true beauty of Costa Rica beach side life style. It’s been a dream to have one of these beast.
With the purchase of this unit, I have been spending a lot of my time bringing it up to excellent conditions. So far, things are going extremely well. Spending a lot of money on new parts with my travels back to the USA.
Once in a while I may ask for your help. Please be patient with me.
Thanks in advance for your help.
Regards: Dexter
Cargo bags
Look for 2 if these bags . I have paypal and shipping to Canada would be needed. Pls email dbmuise@msn.com as I would see it more than on here. Thanks