Category: Forum News

I have a 4” lift kit with HD springs, Axles, the whole works. Not I’d like to put taller tires with wide wheel. The current setup is factory 25x8x12 in the front and 25x10x12 in the rear. I’d like to go with 28x10x12/14 in the front and 28x12x12/14 in the rear. What offset do I need for the new wheels?


Sent from my iPhone using Tapatalk

Just picked up an 04 "Bombardier" Outlander 400 Max XT, curious as to how much it shares with the "Gen1" Can-am bikes? I've had G1 outtys in the past, and at first glance, I'm not seeing a whole lot of differences between this one and my mind's eye. I guess most specifically I'm curious if anyone's fitted SuperATV's 4" GEN1 lift onto an "older" Bombardier. I tried searching didn't find anything, didn't see any sticky anywhere. I woulda thought others before me would've asked these same kinds of questions, but I can't find any useful info. Thanks gang,

Hope someone can help me with this. I have a 2002 Polaris sportsman 700. I completely rebuild it (pretty much). It was running pretty good until I took it for a trail ride. About half
way through the ride it shut down. It would start but when I gave it gas it would just bog down and die. I could feather the gas and it would eventually take off or if I pulled the choke.
I though it was the carb so I clean it out, that didn't help so I replaced the carb. No change. I also replaced the fuel pump, checked the spark plugs and wires. Pulled the heads and check
pretty much everything else, checked the fuel lines and anything related to the fuel system. I am at a stand still. Does anyone have any ideas?

Thanks
Eric G.

Hope someone can help me with this. I have a 2002 Polaris sportsman 700. I completely rebuild it (pretty much). It was running pretty good until I took it for a trail ride. About half
way through the ride it shut down. It would start but when I gave it gas it would just bog down and die. I could feather the gas and it would eventually take off or if I pulled the choke.
I though it was the carb so I clean it out, that didn't help so I replaced the carb. No change. I also replaced the fuel pump, checked the spark plugs and wires. Pulled the heads and check
pretty much everything else, checked the fuel lines and anything related to the fuel system. I am at a stand still. Does anyone have any ideas?

Thanks
Eric G.

Now through October 28th, 2018, save $100.00 instantly on purchases $400.00 or more on select Discount Tire Direct eBay Listings using coupon code PTIRES18 at checkout!

Shop Now: eBay Store | Discount Tire Direct




***ENDS 10/28/2018 | Limit two(2) purchases per eBay Buyer ID***

Now through October 28th, 2018, save $100.00 instantly on purchases $400.00 or more on select Discount Tire Direct eBay Listings using coupon code PTIRES18 at checkout!

Shop Now: eBay Store | Discount Tire Direct




***ENDS 10/28/2018 | Limit two(2) purchases per eBay Buyer ID***

Now through October 28th, 2018, save $100.00 instantly on purchases $400.00 or more on select Discount Tire Direct eBay Listings using coupon code PTIRES18 at checkout!

Shop Now: eBay Store | Discount Tire Direct




***ENDS 10/28/2018 | Limit two(2) purchases per eBay Buyer ID***

Anyone have a line on some companies making skid plates for the new a arm design? Looking for a kit, preferably aftermarket.

Koomafloo.

I currently have 25in tires on it and i was thinking about putting 28in outlaw 2s on it but i was worried about if it would rub so i went to the dealer and asked if the atv could fit the tire and handle the weight cause its a 44 pound tire they told me yes if u have it in low you can use the tire but im still curious on if its true or if there trying to set me up so if it cant handle it i go to them to get sh*t fixed so they get more money. I also was gonna put 2in wheel spacers on too. I wanted to know if anyone else knew anything about if it can handle it and if ill increase my ground clearance and stuff like that.

WHat's the difference between Bighorns and Bighorn 2.0? Also as im looking on Ebay and other places I see HU9 and HU10 in part number, what would this difference be? I need to get two new rears for 2018 RZR 1000XP and not sure what to order?

THanks