Category: Forum News

Hi does anyone know where to get a replacement cover for one of these boxes , I have lost my cover and BRP does not sell the cover speratly . I’ve searched the internet and can’t find any aftermarket part for it either . Any help would be greatly appricated

Hi,
My brother got himself at 2013 a brand new trail blazer 330.
And now he gave it to me, and it has some problems ( the rear axle is bent from his crash) and I am thinking to my self is it the time to let him go because it feels q bit underpowerd to me and get another atv or even utv.
Or maybe try to rebuild it.

What is better worth the money in your opinions?



Sent from my SM-G950F using Tapatalk

Trying to find a pig tail for my 550 xp i tried otb but its not correct ? Its for the t bap,map sensor on the intake any one have any links ? Does polaris sell a repair kit

Hey, Bud from NH, 2 days ago I picked up a 2019 Outlander 570dps. Been riding for 42 years, my current road bike is a 09 street glide.

So I am looking for a helmet for my daughter. She loves to ride with us but hates the noise of atvs. She's only 4. Any recommendations on sound reduction or sound reducing helmets for kids?

Any recommendations or suggestions would be appreciated.

What’s up guys! I have a 06 sportsman 800 on 29.5 outlaws and I can’t keep a exhaust manifold gasket intacted for more then a couple of rides. My right front tire hits the exhaust pipe when at full turn to the right. Of course this is the reason in keeps blowing, but I just wanted to get some opinions on fixing this. Are wheel spacers my only option? Thanks!

I posted earlier about my u-joint on the drive shaft off the gear box had a catastrophic failure. With the shaft removed, the yoke going into the gear box had a bit of play up/down & side to side so I figured that the bearing was bad and needed to be replaced. I have pulled the engine/gearbox and after examining the yoke the bolt that holds it to the shaft was backed out a little and when I tightened it up the play was totally gone. So it appears that the bearings are good after all. The question still remains if there are other issues inside the gearbox. And my main concern is the fact that when the rear shaft was off (no power going to the rear wheels) that at first I was able to put it in 6 wheel drive and the front wheels pulled me forward and in reverse but then just after a few feet it quit working.
So my question is has anybody ever had to drive their 4x4 with the rear drive shaft disconnected and using only the front drive. It would seem to me that you should be able to do it, but maybe there has to be some back pressure on the gearbox rear output shaft for the actuator to properly work. I’m really not looking forward to tearing into the gearbox, and if anybody knows anything about this, I’m all ears.

I've got a 2018 450, when I turn right around a corner at 25mph or above, it will vibrate. I feel it more in the handlebars but I feel like it could be coming from the rear. The best way to describe it is it feels like gears are grinding, just without the noise. Left turns are fine though. Any ideas? Tia

I have a 2015 570 Sportsman. A friend gave me an older plow set up (Mid and rear attachment) that I was able to adapt to this quad. I'm putting a Linear Actuator lift on the front rather than using the winch. The quad has a front bumper bar and I was wondering if the upper and middle mounting points above and below the radiator are strong enough to attach the actuator for the lifting point? Any mounting place lower interferes with the angle lever. I don't imagine the lift weight of the plow assembly is much over 50 lbs so stress on the mounting points should be reasonable. Any thoughts? Thanks.

So i put a 2” rox riser in, trimmed some plastic, cut one zip tie, and removed the bolt holding the front brake junction in place. Anywhere else I get get a little slack in the front brake line? It’s right in the edge of making me uncomfortable about breaking it.


Sent from my iPhone using Tapatalk