Category: Forum News

What flex bar bend is everyone running? I am getting 2 in riser and can’t decide on the bend I am 6 foot

All, I have a 2005 Traxter XL. From when I got it, the speedometer was not working. Now the left side of the handlebar is not working. It will not start with the start switch however, will kill the engine. I can start the quad by jumpng the starter solenoid.
It also does not want to switch gears with the thumb shifter.
I went to a BRP dealer and was told it sounded like a wiring issue including the speedometer. I tried to buy a manual and could not. He advised same is no longer available to purchase.

Does anyone at least have the wiring diagram so I can try to figure out what is going on? He advised that the 2005 had more relays, etc than other years so trying to figure it out.

Thanks in advance for at least reading.

Hi Every one, need to replace the starter on my son's DS90, the Shaft Idle Gear was also was missing a couple teeth. My question is once these are replaced, do these gears on the starter and the Idle Gear need to have any grease applied? Do you want any grease on the clutch side of the the crankcase?


Thanks for any help and advice.

Hi all,

Starter finally died on this 1987 Trailboss. Trying to find an OEM number in order to obtain a replacement. For now I am still starting it using the pull rope, and rather not tear it down and disable it by removing the old starter as it is a pain to R&R. Many starters listed on Ebay for 1990 and up. Nothing for earlier models although they may work. vendor says he needs the OEM number off the starter so hoping someone here has that OEM information.

Thanks in advance.

Backncardr

Just picked up a 2015 1000xxc digital camo, had it on a small run last weekend without issue. Had it out today and it started to show the wrong gear, would be in H but show R or N etc. Sometimes would just show E and check transmission on the dash. Towed it home and washed it, pushed it into the garage and turned the power on and everything was working correctly. Would show correct gear etc.
Im going to change the gearbox oil, clean speed sensor but other than that what could be the issue?
Could the gear selector sensor be on the way out?
Gear oil was fairly dark, id say it was in need of a change quite bad.
Bike has 6000km
Any ideas?

Sent from my SM-N920W8 using Tapatalk

Hello,is it good for Can Am Castrol 4t oil 10w40 power relase-superior acceleration....thanx

Battery died, replaced battery, getting power to the fuse box but fuses for accessory, drive, lights start are showing no power when tested, will not turn over, no lights no nothing... help please

05 phoenix 200 no spark--after a ride I turned of the key and then no spark-engine cranks fine-I have his & hers 200's swapped ign control no change-did the white/brown white disconnect--no spark--coil is fine--have power to the 2wire plug @ ing mod-ground wire ck's good--wire from the controller to coil is ok

Next purchase will be a light bar. No way I’m paying $360 for the Can Am setup, even tho it’s plug and play.

What I like about the Can Am version is that the light bar will NOT turn on without the key. I assume it’s how their harness is prewired with the switch.

Soooo...I see a bunch on eBay and wondering what harness works the best. Anyone buy a specific one that worked perfectly? I’ll also order the Can Am rocker switch to match my others.

Trying to save some $$$$. I’m a novice when it comes to wiring accessories, which is why I prefer plug and play, but willing to try a non-Can Am on this project. :angel

Thanks.

Next purchase will be a light bar. No way I’m paying $360 for the Can Am setup, even tho it’s plug and play.

What I like about the Can Am version is that the light bar will NOT turn on without the key. I assume it’s how their harness is prewired with the switch.

Soooo...I see a bunch on eBay and wondering what harness works the best. Anyone buy a specific one that worked perfectly? I’ll also order the Can Am rocker switch to match my others.

Trying to save some $$$$. I’m a novice when it comes to wiring accessories, which is why I prefer plug and play, but willing to try a non-Can Am on this project. :angel

Thanks.