Category: Forum News

I bought a non running 2004 Trailblazer 250 and after getting it all apart it seems the issue is with the spindle that goes inside the engine from the oil pump. I planned to block it off but the dang thing won't come out. Any ideas?

Has anyone tried Braven Ironsides?
Looking at putting 4 28/10/14 on my commander 1000 xtp.
Thoughts?

Hey folks.
New to this.. I own 2014 Commander XTP. Bought it new in 14 and have just under 13,000 kms on it.
Love this thing!

I have a 2007 Sportsman 700. Recently I have gotten a slight lean in one of my tires. In checking I have a little play in the A Arm. Here is my question. Should I replace bushing only or get a complete kit with new rods, nuts and bolts etc. In a visual inspection they seen fine. Thanks

I have a 2014 outlander max 500 on tracks and the problem is when you turn the key on you hear the fuel pump priming up when you press the start button nothing happens the bike is in park and even tried putting the brake on and still won't start nothing won't even turn over , now if you tent the bike up and put heat on after 60 mins of heat the bike will start

would anyone know what a fix for this could be


Rob

Has anyone installed or had installed a super atv 6 inch lift on their XMR 1000 And if so how does it hold up. As in are the axles still a problem

I am a newbie ATV/UTV rider. I thought it was tough deciding on a UTV...will buy a Maverick Trail DPS 1000. I will use this UTV for hunting and general trail riding...not much racing? I have been all over the "what's the best helmet?" sites but most sites are talking about motorcycle helmets and very few talk about ATV/UTVs. I've looked at the different styles, advantages etc but need help with what UTVers use. Thank you for your thoughtful input!

I know I could use earbuds, but I dont want to go that route. Looking into the soundbar or maybe memphis audio. Curious to hear from you guys about what else is out there and what other guys are using?

I'm looking for a full exhaust system with an O2 sensor for my 2017 sportsman 850 but can't seem to find one. Any recomendations?

Hey Everyone,

So this winter I sold basically all the aftermarket parts on my XMR 800 to a fellow rider except for my Power Commander V and my Straightline Exhaust. The plan was to move to a new Can-Am but I've pushed that off till later this year. So that means I sold my CVTech clutch and secondary springs as well.

So I decided I would go the budget route and see just how much performance I can squeeze from the factory clutches.

Issue #1 is the non locked sheaves on the Renegade/Outlander Primary Clutch. Can-Am Turbo Maverick clutches are still very expensive on e-bay but come with the locked sheaves from the factory. So instead I'm going to send my stock Outlander clutch to UATV-tech.com to have the modification done by them. For $225(US) it turns my Outlander clutch into the Turbo Maverick clutch.

https://uatv-tech.com/products/100-o...odification-us

Issue #2 is that the 800 XMR comes with the same identical clutch set-up to the standard Outlander. Same springs, weights, and helix. The only difference is the 800 XMR receives the 650 Transmission. So because I wanted to keep this budget I looked for BRP weights I could use to get the shiftout to where I need it. So I will be going with the Renegade 800 clutch weights which have a better profile and a lighter weight. Right now my shift out is 6600-6700rpm.

Issue #3 is that because of the tall 30" tires the XMR comes with the clutch is often far too slow on back shifting. I'm going to correct this by using a 650 Helix and keeping the stock 800 XMR Spring. This should significantly improve back shifting and keep the revs up higher.

The idea of these modifications was to improve the clutching without buying a new primary. If someone sourced the weights and helix used this mod could be done for significantly less then a new primary.

I'll update everyone with a video on the channel once I've received the clutch and parts.