I’ve got a 2016 Sportsman 570 X2 and I’m looking for good ideas to put a Garmin Montana w/Ram Mount and a side view mirror. I’m looking at the handlebars but seems like some much stuff already there that I couldn’t find room. Not fond of the idea mounting the mirror off the front rack extension due to vibration. What do you all do?

Thing is a gripper for sure, just gonna take some getting used to in the looks department.
Installed it about an hour ago and already growing on me.
When it comes to looks I generally love what I come up with, but on the fence with this one...
Attachment 104713

Attachment 104721

Attached Thumbnails

   

I have a 2010 Sportsman 500 that the Exhaust Release exploded and came out the side cover plate. I heard it go when I started it and did a quick look and drove it a little not much but then I heard the oil leak that goes with that. . I didn't run it out of oil but it was low. I cheaped out and ordered a new cam on Amazon that came with the cam, sproket and release mechanism. Changed the oil and primed it. I set the valve lash to a tight .006 but I have an annoying rattle that reminds me of valve rattle when I give it some RPM it starts about 2500 and gets worse as you go up. I rechecked the valve lash and it is good. I replaced the Starter Bendix gear as with a stethescope it sounds like it is loudest in that area. Any other idea's? Thinking about a timing chain or maybe the cheap chinese cam has an issue with the compression realease an is rattling? I am out of real solid thoughts and grasping now.

I'm replacing the hub coil on my 1999 sportsman 500 and I have read a lot of post about how important it is that there is no damage to the inner pole the part that the coil slides onto. That if there is damage to the inner pole this can greatly affect the clamping strength of the armature plate to the coil. My problem is that the armature plate is not holing good. When I ohm out the coil and turn the the axle it goes from 30 ohms to 15 ohms so I'm sure the coil is no good. When replacing the coil I noticed that the inner hub pole is slightly mushroomed I had to file the outside edge just a little to get the coil to slide on. Also the inside of it has a little sharp edge on it by the outer axle bearing race. Do you guys think this will be ok? also do you think I should knock the edge off of the inside of the hub by the outer axle bearing race or just leave it alone?

Anybody found reasonable priced piston and ring set for a 200 Phoenix?

I just got through replacing the u joints for the front prop shaft on my 2015 scrambler 850 and I noticed something weird about the shaft itself. Everything I’ve ever learned/ heard/ done with drive shafts it was always very important that the u joints be clocked the same. So why on the front drive shaft are they 45* out? Doesn’t that cause excessive wear on the joints themselves? Someone help me before I take the shaft to a machine shop and have them correct it.


Sent from my iPhone using Tapatalk

I have a 2010 Sportsman 500 that the Exhaust Release exploded and came out the side cover plate. I heard it go when I started it and did a quick look and drove it a little not much but then I heard the oil leak that goes with that. . I didn't run it out of oil but it was low. I cheaped out and ordered a new cam on Amazon that came with the cam, sproket and release mechanism. Changed the oil and primed it. I set the valve lash to a tight .006 but I have an annoying rattle that reminds me of valve rattle when I give it some RPM it starts about 2500 and gets worse as you go up. I rechecked the valve lash and it is good. I replaced the Starter Bendix gear as with a stethescope it sounds like it is loudest in that area. Any other idea's? Thinking about a timing chain or maybe the cheap chinese cam has an issue with the compression realease an is rattling? I am out of real solid thoughts and grasping now.

Just ordered a air box gasket from OMC for 2018 renegade xmr 1000, what are you guys thoughts on this and is this all i need to go deep:grin???

So, I know these things should be serviced regularly and i'd like to do it myself, and not wait around for a man to do it for me. What are the usual things that need to be checked, replaced etc. ? I appreciate any suggestions and tips. Thank you

I have found a few rear shocks but they all seem to be blown, anyone have any aftermarket suggestions that work


Sent from my iPhone using Tapatalk