Author: Forum News

I think my RPM's may be creeping up during shiftout after my re-flash and want to give this clutch tuning a try. I have a REVX. The thought of doing this solely based on watching the tach/speedo was not something I was looking forward to though. I then remembered about a GTech Pro RR meter I have brand new in the box! Among all the 1/4 mile, 0-60 times, trap speeds, etc I can also have it graph RPM vs TIME during a 0-60 run which will allow me to analyze my RPM's as I make a run to 60mph or even the 1/4 mile if I wanted to. I can also upload it to my computer and view all the data using GTech's software. It's the closest thing I have to having my personal dyno and MUCH easier than trying to monitor speed and RPM's while riding. I can log all this data at either 10 or 20 times per second and use it to display all sorts of graphs.

I just don't know if it will work like I would want it to. I'm more concerned about the RPM sensing through the 12V signal. One has to go through a calibration process to get the meter to learn the signal based on varying RPM's. As far as the times and stuff, they don't have to be super accurate, just consistent enough to show changes from different clutch weights. Has anyone tried using one of these to tune their clutch? I would think it would be much better than trying to do your own data logging off of reading the gauge cluster....lol

Here's the manual for the one I have. http://www.gtechpro.com/manual/RR4.0.pdf

Just bought a 2015 SPORTSMAN 570 EPS, it came with 27" ITP Mega Mayhem tires. The tires seem to have plenty of room,in the problem areas, but the seller also had some 1" wheel spacers for it that he claimed were to make the ride a little more stable. My question is if I install these spacers ,will they have any adverse effects on anything else( wheel bearings, suspension, etc...). Please let me know! Thanks!

Hello, I am new to these forums. I recently purchased a new Polaris 450 HO. I was curious to see if other 450 owners upgraded tires right away or made other mods first. Any feedback would be greatly appreciated.

Thanks,

Johnny

I have an idle issue with my ATV. I have gone through the carb and cleaned it and replaced the main jet and air jet. There is some kind of jet or something in the carb body under the float bowl that is called an adjuster on partzilla, its number 34 in the diagram. I cannot get it out, the slot is damaged and it won't back out.

I don't know where the mixture screw is I saw discussed in the sticky thread.

I have replaced the fuel lines and filter to the carb as well.

The issue I have is when riding and I come to a stop, the idle will often, but not every time, drop to low and the machine will die. It will start back if I blip the throttle. I did not do this until I ran out of gas, but I have cleaned the carb and done all the above since.

Any suggestions for how to get "adjuster" out, or where to look to fix idle issue? I can raise the idle speed, but then when it doesn't cut off it idles to fast.

Not sure how this happened but I the display used to show the Gear I was in but now nothing shows up other than two lines _ _ on the display.
Any Ideas as to how I can fix this?

Hey guys, I need some opinions. I bought a 2017 Reno 1000 XMR back in January. It is awesome but life has gotten in the way of my riding for fun. I really need a side by side for the Farm really bad so I am think about getting ride of my Reno for a Defender. Maybe when life slows down a bit i can get me another one. Wish I could keep it but can't have both. What is peoples opinion on how much it might be worth? I know I will take some of a hit but was hoping not to big of one. I bought it new in January and it only has 8 hrs on it. Has just been sitting in my garage (looks brand new).

Hi all,
My sportsman 700 needs a battery. I'm looking around and they seem to run $100 to $150. is that normal?

I recall 300 cca batteries for the lawn tractors and they run $25-$35 at sears or wal mart.

Is there a more economical alternative?

I see many motorcycle batteries at wal mart for $40-$50 that are a bit skinnier then the stock polaris theyre the same height and length but theyre skinnier at 3.5" and the cca's arent listed. am wondering if one of those would work. I'm aware I've got two cylinders and it needs some cca's.