So I’ve got this 400 pulled the shift linkages off to adjust now it’s stuck in either high or low can’t get neutral or reverse and conveniently enough a 12 mm 12 point socket fits it I can only get it to move about an 1/8 inch either direction any ideas
Gsp xtv axles?
Long story short I ordered demon HD’s, and received gsp xtv axles instead lol, anyone have any experience with them? Broke my right rear axle twice in less than 5km so that’s what prompted my upgrade to heavy dutys
Ignition switch trouble shooting
I have a Can-Am 2009 r xt 800 which has no power to the Pod or gauges there's no power at all I have power going into the fuse box relays. I'm going to test the ignition switch which I do not know how to test and looking for ideas and other than that wondering if anybody else knew what was wrong with my 4-wheeler why it's not getting any power
Reading the codes
I've been getting different codes when trying to figure this 700 out.
It had been a 51 code and I guess I got that fixed and miss read it and was then a 61 code but was still getting a check engine light. It is now giving me a 21 code followed by the 61.
So now what do I look for with code 21
I posted before I installed new plugs injectors crank sensor and fuel pump and have gone through the wiring.
Thanks
It had been a 51 code and I guess I got that fixed and miss read it and was then a 61 code but was still getting a check engine light. It is now giving me a 21 code followed by the 61.
So now what do I look for with code 21
I posted before I installed new plugs injectors crank sensor and fuel pump and have gone through the wiring.
Thanks
Reading the codes
I've been getting different codes when trying to figure this 700 out.
It had been a 51 code and I guess I got that fixed and miss read it and was then a 61 code but was still getting a check engine light. It is now giving me a 21 code followed by the 61.
So now what do I look for with code 21
I posted before I installed new plugs injectors crank sensor and fuel pump and have gone through the wiring.
Thanks
It had been a 51 code and I guess I got that fixed and miss read it and was then a 61 code but was still getting a check engine light. It is now giving me a 21 code followed by the 61.
So now what do I look for with code 21
I posted before I installed new plugs injectors crank sensor and fuel pump and have gone through the wiring.
Thanks
Gsp xtv axles?
So I ordered demon HD axles, and got gsp xtv axles for my bike, any opinions on which is better? 2” bracket lift and 29.5 inch swamp lites, I need the better option, do I put em on and run em, or return them and get the demons?
Limp Home
I have a 2017 outlander 570 its over heating fan not working , I have checked relay and fuse also un plugged fan and tried direct 12v still dose not work. Any other suggestions before buying new Fan ?
1999 sportsman 335, I need a new cam
I'm looking for a cam. The bike was bogging out at full throttle. Rebuilt the carb now the bike wont go anywhere, no power. I was told I need a new cam shaft. Polaris discontinued the part. I been searching the web, No luck. If anyone has one or can point me in the right direction please email me. jeff.gimon78@gmail.com
Radiator hit by stone
It got hit by a small stone, will this be an issue? It’s not overheating or leaking yet.
I did order a protector screen for it.
I did order a protector screen for it.
02 325 Magnum carb rebuild ?
2002 325 Mag. - I rebuilt my carb. with Moose kit 1003-0513 because I wasn’t getting enough gas or no gas to the carb. and everything else checked out. I also removed the screen/filters inside the gas tank and cleaned. Air filter & fuel pump is new.
2 things I noticed during disassembly were my air/fuel mixture screw didn’t have an o-ring or washer like what is in the kit. Also the main jet I removed said 120 and an “R” with a little square box next to it. The new main jet had 145 on it, which I installed. I also installed the new mixture screw with spring, o-ring and washer. I made sure to turn the original air/fuel mixture screw in before removing which was 2-1/2 turns.
When I fired it up it ran great, idled well, rev’d it a little and ran smooth but when I opened it up it makes a steady chatter noise like it isn’t getting enough gas or to much? So my question is – do you think the main jet is the wrong size from the kit ? Or your thoughts that might be causing the problem ?
Greatly appreciate any knowledge on this !
2 things I noticed during disassembly were my air/fuel mixture screw didn’t have an o-ring or washer like what is in the kit. Also the main jet I removed said 120 and an “R” with a little square box next to it. The new main jet had 145 on it, which I installed. I also installed the new mixture screw with spring, o-ring and washer. I made sure to turn the original air/fuel mixture screw in before removing which was 2-1/2 turns.
When I fired it up it ran great, idled well, rev’d it a little and ran smooth but when I opened it up it makes a steady chatter noise like it isn’t getting enough gas or to much? So my question is – do you think the main jet is the wrong size from the kit ? Or your thoughts that might be causing the problem ?
Greatly appreciate any knowledge on this !