News

I bought a new 16 570 sportsman in the summer of 16, that winter I did the first service at 15 hours in preparation to plow some snow. My initial plan was to change all the fluids once a year but I got busy and didn't go on any rides. As of today it only has 25 hours on it, no mud no water just work around my property. I have changed the oil and filter but curious about the other fluids, it's been about 14-16 months but only 10 hours of riding. Needless to say we have had no significant snow to plow so it hasn't seen any hard work.

Because of an injury I haven't been able to ride much. But I need my Wheeler to work when I need it.

I Started it recently to move it out of the lawn mower's way - ran fine for a few minutes. When I went to Re-Start it it cranked FOREVER then backfired REAL loud. Now it won't start!? It fires while cranking - maybe twice, Put Put - but will not run and stay running.

It has been running a little rough and back firing but it goes away after it runs for a while. I always make sure to get it to operating temp before it sits for weeks.

I am lost on how to trouble shooting this - I've read lots of No Start posts here and am spinning my wheels. There are no codes on the display. When I turn the key to 'On' I hear what sounds like water boiling near the fuel tank - is that the fuel pump?

It is due for factory service in 5 hours (the thing has under 700 mi on it and I had to replace the fan last year!) Other than that The thing has NEVER given me any trouble. I prefer to NOT take it to a dealer. I do most of my own maintenance and I WILL say that I take very good of this and all my toys.
I'm stumped - Any suggestions for me?? I'll give more info as needed.
Thanks in Advance
JS

I just got my 2018 Sportsman 1000 XP Touring edition and I want to install a snorkel kit. Called Highlifter and said they dont make one for the touring, only for tge regular 1000. Anyone in my situation or know what snorkel kit will fit?

Just wanted to say thanks for the ad.... just purchased a new 2017 570 that is being taken out of the crate and put together as we speak. Looking forward to being a part of this forum. Cheers.

It's not too pretty to get dirty

There’s no doubt about it, this is one wicked Polaris Scrambler XP 1000. It’s not at all uncommon to find folks who spend a ton of time and money outfitting a great looking mud ATV, only to keep it out of the mud. That’s definitely not the case with the Sinister Scrambler as it’s owner is not shy about getting it dirty.

ATV.com recommends that ATV riders always wear a helmet when behind the bars.

Sinister Scrambler: Modded Mondays - ATV.com

I picked up an '18 Outtie Max XTP 1000 last week. I have a few potential issues that I was hoping to get some feedback on:

Condensation in gauge - Is this normal? Is there anything I can do to prevent it? I can get it replaced under warranty but that is not much help if it will just happen again.

Backfiring - The bike seems to backfire once in a while slowing down (engine braking). Is this normal? My 800 never seemed to do that.

Bike seems like a huge improvement over my '09 shortie. The shocks are night and day better and I really like the max. The power steering is a great addition as well. I snorkeled the bike with the brp kit (looooong install) and added a bunch of dei cool tape and some floor and tunnel shield to various spots to help keep things cool. Looking forward to many enjoyable miles on this one.

Thanks

I just replaced the carburetor and the atv starts and idles fine, but once you push the gas it bogs and stalls. If I open the choke about 1/4 it will run and drive fine. It's got fresh lines, filters and gas. What could be the issue....I know the gas gauge parts broke and fell inside the tank but that shouldn't matter should it? Any suggestions what to do next I was going to pull the tank, dump and clean it out as my next resort????

Just purchased an 18 base 570 and would like to change all the fluids. Is the Trans fluid separate from the Rear diff. fluid? Apologies if this is probably a silly question but I am new to this. Thanks

hi, I just bought a 2012 sportsman 550 XP EPS. Noticed the front wheels wouldn't engage and found the axles very loose and I could almost pull them out of the differential. Took it apart and found that the axle splines look in good shape but the splines in the front differential are almost smooth. Anybody know if this is repairable, are just the outer spline housings available or does it have to be the whole hub rebuild kit they sell for the front diff?

Does the differential have to come out to do it, or on the side with all the bolts, do all the parts slide out of the differential? Mine has EPS so it looks like a major pain to take it out of the quad.

Looking for a cover for my 2017 outlander 650 XT as it will be stored outside all summer. I have a rear box/seat on the rear rack as well.

Any suggestions


Sent from my iPhone using Tapatalk