News

I bought an unknown year tb 250 lower on ebay and the inner seal on the old one (98)had a retainer ring with screw holes in the block to hold it on. the new one has no such holes. can anyone one help me figure out the year and or how i can secure it? Picture is of the new lower.

Attached Thumbnails

 

2011 outlander 800. Will not crank. Turn on heat fuel pump, lights on and hit starter....no start lights dim, clicking in starter solenoid on back by battery. Installed new battery. No change. Check starter terminal and have 12 volts there when pushing starter button. Bad starter?


Thanks guys


Sent from my iPhone using Tapatalk

05 magnum 330 4x4, can get into all gears nice n smooth when I first start it but after its warmed up it's hard to shift the lever. It will go into H L R P but neutral is very hard to find. Thanks for any suggestions!


Sent from my iPhone using Tapatalk

2000 Sportsman 500 with steering wobble... have had quads before ( Banshees) don't need to go the speed of light anymore... I bought this from my Father in law, he bought new... needs a little maintenance but great quad.

0

Bought 2 new 2015 ATVs beginning of 2016 Polaris sportsman LE 1000. Love the motor power and Fox shocks.
From day one I have complained they do not shift from a dead stop, while riding at high altitude. Above 10K feet. You have to turn eng off, shift then back on. because at a dead stop eng RPMs continues to fluctuate from 1200 to 1800. Dealer has not been able to fix nor do they have any idea what to do. They say they have been in contact with Polaris but no answers. We have broken the shifter splines which they have replaced. They have tried to adjust clutch several times. Nothing added on after market. They say they tried to re-flash computer, did not help. happening to both machines. NEED HELP!!!!!! Has anyone else had this problem and did your dealer fix it? At this point dealer saying they don't know what to do. Im thinking about just selling and going with a different brand.

Hello fellow Polaris riders-I have an 04 or 05 TB 250 complete engine that needs a fresh top end. Bottom end is tight an would be a great way to easily freshen up an older TB w/loose bearings.

Its complete-not torn down w/stator. No Pullstart. 100.00 u pay ship

Hello everyone, our names are Leiann and Jim and we are from Peoria, Arizona. We love riding our Can Am Commander in the desert and through the Az. mountains. Have had it for almost a year now in October and have added quite a few items to the rig. Too many to mention. But with this heat we have to travel up north to ride.

Hi All,

There is a new Warranty Bulletin, Campaign #2017-0008: CAB Models - Air Infiltration in Very Hot/Cold Temperatures.

This bulletin addresses the concerns in regards to openings in the front end of Defender vehicles that allowed air to infiltrate the cab.

2016 and 2017 model year Defender Cab models as well as models with the BRP rigid CAB enclosure sold as an accessory are subject to the bulletin. Please check with your dealer to see if your unit is affected.

Thanks,

Owen - BRPcare

Any help or opinions are greatly appreciated, I have a 2008 Sportsman 800 with 1200 miles of light use, I have owned since new. Due to a 4wd problem (constantly locked in) I took out my front differential hoping to find the common blown up sprague cage, well that I did not. Every thing appears to be in great condition and intact other than when I took it out the output pistons and parts on the drivers side I found wrapped around the output pistons was a bunch of black plastic material. It appears the piston was rubbing against the black plastic ring section that comes as part of the case on both sides. I assume it is some type of a coil or something? Not sure if this is supposed to be touching or not. It almost seems like in a manual transmission you have the flywheel and pressure plate that might be slipping causing it to melt off instead of making full contact? Just not sure how these 2 parts are supposed to mate or not touch at all. I assume the 4wd is locked in because of the mess that I found. If you look at the second pic I also have 2 pretty good grooves worn in the armature piece not sure if this is supposed to happen? I posted a few pics first should show the wear/melting on the whatever its called, second shows the mess on the workbench and third shows the melted pieces that are from the first pic. The passenger side does also have some wear on it but no real debris. Thanks to all who can help and hope I put this in the right section. If not please advise.

Attached Thumbnails