Any can am discount codes for accessories. Or anything coming up in the near future?
2004 330 atp
I need some fresh "eyeballs" on this one. This 330 will start and idle, but with a bit of throttle it dies. With the choke on it will rev, although, somewhat sluggishly. I just got it and I'm ready to pull my hair out! It has a brand new carb and intake boot. Fresh, clean fuel is in it. Compression is almost 120. I even checked the bolts that mount the intake boot to make sure they weren't a hair too long. I had that happen on a dirtbike once. I didn't replace the carb and boot. They were on it when I got it. I even tried a gravity feed tank( although it was a pretty hokey setup and I might try something different if nothing else works) and it still isn't right. So, IDK if the fuel lines are routed properly.
#1 goes to the carb on the right side
#2 goes to the petcock
#3 goes to the inlet on the carb
Does that look right?
#1 goes to the carb on the right side
#2 goes to the petcock
#3 goes to the inlet on the carb
Does that look right?
Hey, jcling from pa
New to the forum. Just purchased a 2019 maverick sport 1000R. Love it. From pennsylvania.
Good to be hear and maybe learn something and find some cool aftermarket stuff.
Yeeeeaahhh!
Good to be hear and maybe learn something and find some cool aftermarket stuff.
Yeeeeaahhh!
Hey, jcling from pa
New to the forum. Just purchased a 2019 maverick sport 1000R. Love it. From pennsylvania.
Good to be hear and maybe learn something and find some cool aftermarket stuff.
Yeeeeaahhh!
Good to be hear and maybe learn something and find some cool aftermarket stuff.
Yeeeeaahhh!
New to the forum
New to the forum. Just got a 2019 SP 850 Premium Edition. Picked it up late on friday so I wasn't able to get insurance. So It sits till monday.
Ready 2 Instal Plastic Skid Plates
Just joined forum and have read a lot of good threads seems there are lot of good people here offering up good advice.
Always try to do as much of the service work as I can, saying that here I am about to (TRY) to install plastic skid plates purchased from my Can AM dealer for on my 2019 850 Max XT
I did install a aluminum set on my 2015 500 Max Xt that kit was a headache better part of afternoon (OFF SHORE RUSSIAN)lots a parts.
Can Am kit has less parts but MY QUESTION??? does the front plate go up under the existing plastic or over and attach to the winch fairing bolts the rest seems straight forward.
Any advice and pictures would be welcome.
Thanks
Always try to do as much of the service work as I can, saying that here I am about to (TRY) to install plastic skid plates purchased from my Can AM dealer for on my 2019 850 Max XT
I did install a aluminum set on my 2015 500 Max Xt that kit was a headache better part of afternoon (OFF SHORE RUSSIAN)lots a parts.
Can Am kit has less parts but MY QUESTION??? does the front plate go up under the existing plastic or over and attach to the winch fairing bolts the rest seems straight forward.
Any advice and pictures would be welcome.
Thanks
Can I get some help on an AWD issue
Riding this week and the engine light came on ,about the same time I realize I dont have 4X4 anymore. The drive fuse was blown. Replaced and went on my merry way. Blew another in a couple minutes dident see any obvious wires that might be frayed or burnt. Got back to the cabin and Pulled code 520207 5 . All Wheel Drive Control,,,Driver Circuit Open/Grounded. The only thing I could think to do was look for broken wires at the switch and where the wires go into the front gearcase.The only thing I found was 1 of the 2 wires in the AWD switch box on the handlebar was pinched. How do I disconnect that wire harness from the switch I couldn't unplug it.
Any guidance on what else and where to look for anything?
2015 850 SP
Any guidance on what else and where to look for anything?
2015 850 SP
’06 Outlander 800 STD -plzHALP-
As I was riding I heard a strange noise as if the belt broke and when I took the cover off it seemed the secondary clutch bolt had come out and stripped the cam gear.
The new cam I purchased is retrofitted for that bike(shown in the picture).
I'm having trouble assembling the retro cam helix and the stock secondary clutch plate.
The bolt will go in but I cannot get the belt tool to expand the plates.
(do I need new plates? and also the new spring that fits into the helix?)
I saw a youtube video that showed a spring that was fitted into tits one in the helix the other in the clutch plate.
I'm not sure of the alignment of the clutch plates either as they came apart when the bolt snapped originally.
Here are a bunch of pictures, maybe you can find waldo.
The new cam I purchased is retrofitted for that bike(shown in the picture).
I'm having trouble assembling the retro cam helix and the stock secondary clutch plate.
The bolt will go in but I cannot get the belt tool to expand the plates.
(do I need new plates? and also the new spring that fits into the helix?)
I saw a youtube video that showed a spring that was fitted into tits one in the helix the other in the clutch plate.
I'm not sure of the alignment of the clutch plates either as they came apart when the bolt snapped originally.
Here are a bunch of pictures, maybe you can find waldo.
Superwinch Wiring
My Superwinch needs a wire from the ignition switch to tie into. There is an open 4 prong plug and two single open wires under the front storage. I assume they’re for the Polaris Winch hookup. Does anybody know what color goes where? It says I need a brown wire from the ignition to the remote and handle bar controls. Thanks.
Glacier 1 plow mount bracket
I am looking for a mount bracket for the Glacier 1 plow system for a 2000 Sportsman 335 part#2874774.i have part#2874773 mount for this system that I believe fits a 2003-2010.If anyone interested in buying it after I find one I need. Polaris says this part is no longer available, so I need help guys!!!