Anyone using a Diamondback cover, and loading from the rear with the extensions?
I have a Ram short bed (5.7’) with the Diamondback cover. I was going to order the extensions but not sure they are long enough, I think I would need 4” more inches . Looking for someone to do some measurements of theirs.
See attached pic.
Thanks
Is there an easier way to connect/disconnect the rear way bar? I pulled the pins to try it out and it seems fine. Now I can't get it back together. I'm not a high speed guy so do I even need it connected? What have you other riders found out while using you wheeler? I'm kind of thinking of leaving it disconnected unless there is something I'm missing like side hilling and such?
Hey guys just wondering whats the best seals and wear rings to buy for my 2015 xmr 800 rear end. OEM or aftermarket?
I know the xmr is geared lower than the other models. Is it possible to get more top end performance out of it?
Sent from my SM-G955U using Tapatalk
I have a bunch of Defender accessories for sale, if anyone is interested
• Hardcoated Full Windshield with 4 Snap Vents – 715002432 - $539.99 - sell-$400
• Defender Front Bumper – 715002418 – 229.99 - sell - $150
• Extreme Front Bumper Plates – 715003005 - $189.99 – sell $125
• Defender Rear Bumper – 715002419 - $249.99 – sell $175
• Brand New (in the box) never installed Battle Armor 2” Bracket Lift – Sell $85
• Super ATV arched rear lower A-Arms with adjustable Caster \ Camber, Black, (New in the box \ Never installed) - $250 - sell - $200
• Highlifter Front Arched Forward A-Arms, Black with all 4 Keller Ball Joints, Garage Products Bushings….. A-Arms - $410, Keller Ball Joints - $534, Garage Products Bushings - $110 ($1058 total) - sell $650
• Jakes Pucks – Complete Front and Rear 2” set – sell $75
• Jakes Pucks Front Only 1.25” – sell $30
• S3 1st series Heave Duty Front Springs Desert Tan - $170 – sell $100
Feel free to make an offer, all I can do is say no 😊
All Prices plus actual shipping, I’m located in Central West Virginia
I can take PayPal
Have a quiet question. I have a 2016 renny 850, and I love it. On the last couple of rides I noticed that my front fenders and clips have been coming loose. The center piece over the air box will come loose and rattle during rides. Is this common? I plan to strip the whole front end down and check for anything loose on the supports. Any feedback would help, thanks.
Sent from my iPhone using Tapatalk Pro
My wifes rene broke its drive shaft. Already have the new drive shaft and ready to install. Just read about these speedi-sleeves. Any one use them and is it necessary before I put everything back together. I have a new wear ring and oil seal. Thanks
The AMSOIL Snowshoe event is one of the most anticipated rounds of the AMSOIL Grand National Cross Country (GNCC) Series, an AMA National Championship, and this year it was no different. This event is a tribute race dedicated to the infamous and legendary Blackwater 100 as it honors that historical race each year. With an abundance of rainfall prior to the race, and on-and-off showers through the race, the GNCC ATV riders would try and conquer a very wet and treacherous mountain.
Hello all,
New to the forum and just inherited an 87 trailboss 250 4x4. I’m having issues with sourcing brake hoses. Two of the 4 are plugged and I think the master cylinder is toast. I’ve scoured the interwebs and Polaris part catalogue and most everything is no longer available. Wondering if anyone has any suggestions for getting the front and rear hoses. Also I saw that the master cylinder seals are still available but once I looked them up they didn’t quite look right. Has anyone ever rebuilt these old masters with new seals?
