News

OK I am new to this forum stuff, so not sure where to ask this. I have a 2017 outlander 570. My parking brake looses holding power after 30 minutes or so and just today, when I had it in PARK it Failed and rolled down the hill. It is fine, it was on a fairly Flat spot. The Factory said do not trust my brake, that is why they made PARK. Well now I can not trust PARK. Has anyone else had any issues with either of these?

Oh and as an Introduction, I am a Ranger for the Boy Scouts and use my ATV for Work only. I have had 3 Honda Rubicon's, 1 Kawasaki and 1 Arctic Cat. So Far this one Pulls a Load MUCH better than any of the others.

OK I am new to this forum stuff, so not sure where to ask this. I have a 2017 outlander 570. My parking brake looses holding power after 30 minutes or so and just today, when I had it in PARK it Failed and rolled down the hill. It is fine, it was on a fairly Flat spot. The Factory said do not trust my brake, that is why they made PARK. Well now I can not trust PARK. Has anyone else had any issues with either of these?

Oh and as an Introduction, I am a Ranger for the Boy Scouts and use my ATV for Work only. I have had 3 Honda Rubicon's, 1 Kawasaki and 1 Arctic Cat. So Far this one Pulls a Load MUCH better than any of the others.

'15 Polaris Sportsman 570 EFI

Only 300 Miles
Pursuit Camo Edition
4WD
26" Rip Saw Tires
Sedona 12" Wheels
No Power Steering
Has Winch (Not Installed)
Stock Wheels and Tires Included
Was Purchased in 2016 as a Leftover
Excellent Condition

$5,995

Located in Atkinson, NH 03811
(30 Miles North of Boston , Mass)

(603) 235-7268

Attached Thumbnails

         

We just got a "new" 2000 polaris scrambler 500. We brought it home and there were a few things we needed to do to it, oil change, ail filter, battery, and adjust the chain.

while I was loosening the bolts the ones in green (standard clamp bolts) went fine, but the third bolt broke off, it is broken about 1/8 inch above the gap in red.

I have a couple of questions

1. is it okay to drive it without this bolt?... I'm thinking not but my wife is really anxous to give her a real spin.

2. what is the best way to get this bolt out? the only thing I can think of is to get a drill bit and try to drill it out, I have never had much luck with an easy out and hardened steel.

Thanks a lot.

Attached Thumbnails

 

Hey all new in town. After years of waiting finally landed an oldie. First one. Guess have to start somewhere.

I have a 2014 sportsman 570 EFI. I have 25x8-12 on the front and 25x10-12 on the rear. If I went with 26x9-14 on the front and 26x11-14 on the rear will I need to do a clutch upgrade? Also what wheel offset would be needed?

Hey guys

I just bought my Dad's 1999 xplorer 400. It has 1600 miles on it. My Dad never tinkered with it at all. It still has everything stock and setup for sea level. That would be fine if we didn't live at 6000ft lol. I'm looking to get a good clutch kit for 6000-9000'. I installed a tach and the most RPM I have seen is 3020. I know the belt needs changed and most likely the jetting. Any suggestions on a clutch kit or setup would be great!

Thanks

Has any one done ceramic coating on their y pipe back to the muffler on a outy 1000 to keep heat down. Mine is the 6x6 but all the engines n y pipes are the same

I have a 2018 XMR 850 and the plastic bracket that holds the shifting linkage in place broke off on me . Is there an easy way to change this out ? Anyone else experience this ?

Hey everyone I bought a 2000 Polaris Sportsman 500 and it's got factory wheels on it. I want to get a new set of tires for it but the Polaris shop told me the front should be 25x8x12 and the rear should be 25x10x12

The rears that are on there right now are 25 x11x12 so I'm a little confused and don't want to order the wrong tires.

Can someone tell me what actual size should be?