News

I'm still messing with the lower lights on my 2011 Can-Am Outlander 500. The machine came with the lights (see picture's). They appeared to be factory installed, but might be aftermarket. The kid I bought the ATV from had unplugged them He said I could get a new harness at Tractor Supply. (I'm suspecting he may have got the light at Tractor Supply also, because the lights have the "TRAVELLER" brand connector.

The left led has burnt out and I am trying to replace it. The 2 1/4" or 56mm light fits perfectly in the opening. The opening is Can-am part # 705002780 called LH lower front facia.

I can't find the TRAVELLER brand lights anywhere.

Has anyone put a light in the "lower front facia" opening? What did you use? Where did it come from?

Sent from my XT1254 using Tapatalk

So i just got a nee 2017 570 eps after selling my beloved hawkeye with only 67 hours 375 miles that i had since new since 2006. It couldnt pull my brush hog very long without over heating and not wanting to run. I also have a 2018 ranger on order but prefer mowing with brush hog with an atv since its more agile and easier to see behind me to watch the hog.

I'm getting the code for the throttle being stuck and whenever I give it a quarter throttle and let off it will keep running at 1600 1800 rpm for about 3 or 4 seconds but the time varies and it will come back down to idle. Cleaned throttle body but didn't fix it. Any ideas

Hello All,

I've been having an issue with my 2017 Sportsman 570 that pertains to the rear RH sway bar link contacting the exhaust muffler when the suspension is at near full travel. I brought the machine to my local dealer and tried to get it checked out under warranty. Since the service manager had never seen or heard of this exact issue, he assumed that I was hiding something from him "there's something going on here that we don't know about" (Jim, Tousley Motorsports Service MN). I pulled it out of the dealer as soon as I realized their priority wasn't to help me but to point a finger at me.

I've never towed or hauled anything; however, I do weigh 240 lbs and certain riding conditions and terrain must be causing this issue. I ride responsibly on state trails and the 4 wheels have never been off the ground. I've spent a lot of time trying to track this issue down online but cant find anything of significance. If anyone has experienced this same issue, please let me know so that I can inform Polaris about the problem.

Thank you very much!

Attached Thumbnails

       

Hi fellas,
I just thought I would share my story. Today I pulled the primary outer half off to service the one-way assembly and clean things up. Everything looked OK but, needing some Isoflex grease. I pulled the 2 bearings out (sealed both sides), wiped them off and solvent cleaned the remainder of the parts. After reassembling the one-way I started cleaning and scuffing the sheaves with some Scotch Brite and then I saw a flat spot on a roller. The unhappiness started then. I just brought the bike home from the dealer after getting the 2,000 mile valve clearance check-yesterday (80 mile round trip). Luckily they had rollers in stock. Then the service man told me it would be under warrantee-if they replaced the rollers but, needed the whole machine. Well I didn't want to lose the bike for the whole holiday weekend so I went to the dealer and bought the rollers. When I pulled in the sales manager greeted me in the parking lot so I related my story to him and he said he would get my roller purchase refunded under warrantee ! I still had to replace all 6 rollers and it took some improvisation but, good triumphed over evil and I got her done!

The moral of this story is: the clutch rollers can develop flat spots in as little as 2150 miles. I purchased this machine in March and have around 80 hours on it. Now to go out and wear out the new rollers!
Mike

Hey everyone! So I stopped at my local dealer today and picked up two sets of the Xenon blue colored 50w headlights. They were on sale for $32 each. I threw them on my quad and they are a whiter light which I like but they seem to be not a bright as stock... Has anyone else noticed this? Do they need a bit to warm up?? How do I get more out of these headlights!!??

Sent from my LG-H831 using Tapatalk

Hey Fella's...quick question. If you have seen the "800 for $800" build thread, you know i'm rebuilding a 2005 Sportsman 800. The owner before me must have flipped the thing because the Speedometer was busted really bad. He gave me a good used Speedometer from another quad that works great. Question is...when i look at total mileage am i seeing the mileage of the Quad i own or the mileage of the previous quad? Basically, does the current speedo record accumulated miles or does the pcm keep the record?

I have a 2007 Outlander 400 The other day I parked on a slope facing downhill and noticed fuel dripping from a little 1/8" tube connected to the bottom of the carburetor. Anybody have an idea what might cause this and also the hose appears to have a metal tube on the end but I cannot find where it should be connected to? Also anyone know where I might find a shop manual that will show it? I went to the dealer and looking at the screen I could not tell where it goes. Thanks in advance for any help on this. I do not want to start a fire.

Hey! I just purchased a 2017 XMR 850, and so far it great! coming from a 07 Sportsman 450, I decided to jump ship after the sportsman finally crapped out on me and I had enough of dumping money into it.

Hey y'all. I'm having a hard time getting my rear drive shaft out on my mav 16 xmr. I need to replace the seal on the shaft/diff bc it's leaking. I've done it before and don't recall this much issue.
I've removed both bolts on both ends of the driveshaft

I've got the 3 bolts on the rear diff off.
Tires off
Rear diff is pulled back all the way. What am I missing?
It's so close to coming out but I'm just short on space by a hair and I've tried muscling it.
Any tips on getting this thing off? Tilt the rear diff up? Tilt it down? It seems I had the most space when I tipped the side where th drive shaft connects upward...
I'm also trying to remove the back side before the front.... sound right? Wrong?
Thanks in advance!