News

Sold my 1992 Polaris and bought a 2011 Outlander 500 EFI.

Recently purchased 2017 650 max. My first Can Am. I've owned Honda, Polaris, and 2 Brute Force's. Very happy with purchase. Looking to install skid plates soon. Will the flex plow mount work with the Ricochet skid plates?

Hey guys I need some help on what i may need to take the snorkels off my wheeler and put it back to stock. Im sick on dealing with the wardens. I bought it with the snorkel its a 2007 outlander 800 so i have no idea what i gotta do to put it back to stock. Please help!!

To those of you who have a 03 05 Magnum. I have ordered a factory service manual for my 04 Magnum 330 4x4. Engine had knock-swapped out identical 330 off 05 I think. Where does the lead of the cdi ( not ecm)-black with bullet connector connect to? Had my grounds and ignition coil run correctly. Thought it was connected to stator lead-cant be right ran fine and was charging for 15 minutes and took out ecm. (&^%&*$$!!!) Only way could get it to fire was connected to stator lead off ecm-must not be right otherwise wouldn.t have damaged it-still fires and runs but can only run for 30 seconds starts to overheat cdi. No longer charging, any help would be appreciated.

I am working on an 09 Sportman 850 and the clutch does not want to disengage. The guy that owns it put a new belt on it and that is dragging and of course makes it almost impossible to shift. On the older machines I have done shims to align the clutches. But the service manual doesn't make any reference to this and the transmission is a a completely different setup. Short of disassembling the clutches what should I be looking for?

Hey guys, im looking for some advice with my new unit, 2015 outlander xt 800.Bare with me please,i'm new to these as i'm coming from a brute force 650 to this. it currently has a new MudnWheels 2.0 rear diff, 27x12x14 zilla tires, radiator relocate, snorkels, new air filter, and a Yoshimira/can am slip on exhaust. I have a buddy selling a PC5 programmer wanting to trade me my outlaw 2 tires that came on the bike when i bought it. its currently mapped for a outlander 1000, is there any one on this forum who can sell or send me a map for my outlander 800 with the pipe? its currently surging a little at idle when cold and will sputter and almost die when cold if you give it throttle to move. if you let it warm up its perfectly fine, seems to me like its lean. Any ideas with this issue? it only has 400 miles on it and i run seafoam to keep it clean. fresh fluids everywhere on the bike also.

Secondly, it is saying key not recognized. If i wiggle the key around itll start just fine. I have a brand new ignition for it here and was wondering what all went into programming it and/or the key to get it to start like it should without having to mess with the key and risk being stranded away from home.
Thanks in advance, i greatly appreciate this forum .

Attached Images

File Type: jpeg

tires1.jpeg (377.1 KB)

So i just finished up my DIY snorkel kit on my 2016 outlander xmr and all that's left are the vent lines. i bought bellows for the front and rear diffs and was wanting peoples input on trying to put a bellow on the transmission. Thanks.

Testing out a billet throttle lever from custom moto out of quebec.
You need a special torx bit to open the drive by wire box

it a tamper proof torx bit, called a ipr15 torx plus bit. It has 5 flutes not 6 like a t15 which is the most common type of torx with 6 flutes and has the hole in middle of bit for the pin that is head of torx screw.

Anybody ever hear of this style bit before ? Couldn't find at any supplier or store in toronto canada. Ordered from a company here called wiha tools and shipped from usa. Was $70 us for a small 7 bit set.
Tried a snap on dealer and gray and they had never heard of it either
now bike up north so wont be able to try lever out till next week

Attached Thumbnails