News

I am getting ready to send my ECU off to Monster. I have seen several members here recommend Monster so before I send it off is there any special recommendations you would have for any settings. I have a 2016 Rene 1000Xxc. Adding a Yosh slip on after I get the ECU back. Other than that it is stock. I ride in the dunes at the coast, mountain trails and in the high desert usually just chasing my two boys.

I have no problem with the engine braking and like it so I don't have to nail the brakes when stopping. I was real curious about the RPM limit and speed control settings. Should I just let the people at Monster make a setting or is there a recommendation from someone?

Bottom line I am just hoping to learn from what someone else did and loved or wished they had done before I send mine off. I would hate to miss something I should have ask for.

Thanks for any advice.

Gonna put some new plugs in my 2014 800 and was wonderin if anyone has used the V Power plugs yet? Looking how they compare to the Iridium plugs.

I was asked to post this in the Repair section - hope to help some folks...

I have a 1999 335 that uses the LR60, and am in the process of repairing them.
I have a good understanding on some of the components and have had luck replacing them.
Why the units I have went bad- NO IDEA - could of been bad connections, arcing, mud in fan causing an overload, but I have fixed a couple. I have collected a few replacement parts for the boards that are the major culprits of failure.
Also working on making my own Thermistors - Having good luck with that too.
Anyone have old LR60, or LR62, I would like to buy if they are no good.
Thanks

Hey all!

I have a couple questions.. this past fall we (the mrs. and i) went on a chilly ride (40*). I wore my hunting boots and a couple layers and was just fine. The mrs. isn't as warm blooded (or as furry lol) as i. Her main source of cold was her feet and hands. She wore a pair of knock off muck boots and some warm socks, and we got some gloves that i had worn when i was a trash man years ago, but they were warmer back then (or maybe it was due to me being younger lol).

I was curious what types of boots would be best for her to wear, but still flexible enough for her?

Also, without getting hand warmers (she hasn't given the OK on those.....yet), what types of waterproof and windproof gloves would be great for that type of weather? (30-40*) We both like gloves and not "mittens".

we have purchased items to cover our mouths and necks under our helmets.

Ended up greasing my rear bearings on my 800 last night. Pretty simple process and went well but a guy on Facebook told me a lot of guys are saying bad things about to much grease when you do it. So I guess my question is how much grease is to much???? Im hoping I didnt screw up now.

New to the Polaris world and have a general question. I have a 2018 sportsman 570 and performing 25 hr service. My question has to do with the rear diff/transmission fill plug. What is the hard plastic looking material that is blocking 95% of the fill hole? Is this normal? Why would Polaris do this? I managed to get the oil back into the machine, but what a total pain in the ass! What method are people using to fill this back up? All answers much appreciated, thanks.

Hello all, I am new to the Polaris world, but not ATVs or dirt bikes. So new to this site with my New to me Polaris.

So I just bought a 2002 Polaris Sportsman 700 Twin for cheap as it is in need of repair.
Has been blowing rad fluid out of holding tank. I figured it was a blow head gasket.

Bought it anyways, brought it home and tried to get the rad cap off but it was stuck which was strange. It would turn, but not pull out. I had to pry it out. It seemed to be baked into there. No fluid visible below rad cap. Wiped off the underside of the cap and it was black with what looked like exhaust residue. Wiped out the inside of the tube and was all black as well. So I can only assume it ran like this for a while.

With the cap off, I turned the key to start it to see if it would pump any rad fluid and all I could see was exhaust pumping through and out of the rad cap holder pipe.

So head gasket is blown. https://www.dropbox.com/s/gdbl9zl08t..._3616.MOV?dl=0

In hoping that the head is still ok, I am considering repairs. I cannot start taking it apart for 3-4 weeks, but just thinking about what needs to be done.

I do not know how long it was run like this, but had to be a while due to the black and baked rad cap. So damage could vary, but thinking
- new rad cap
- new thermostat
- gasket kit

Motor runs well, does not smoke oil and no water in oil, unless it was change after it failed, which I cannot verify. Guy said it smokes a bit of blue when first started but stops when warm. Now that could be a choke issue or warn rings.

I ran it for a very short period of time in my garage with the OH door closed and it did not smoke me out and it was a cold engine. So could not replicate the blue smoke when cold.

So I need to check the head and cylinder for warping.
Will check the jug and may do a light hone and new rings pending.

Check the valves, and replace the valve seals at a minimum.

Would the exhaust heat damage the impeller ? I can see it damaging seals, but does not appear to be leaking, but any exhaust heat damage might quickly show up once I start riding, so I will do those seals as well.

I cannot really think of anything else.

I have never worked on a twin cylinder, but have rebuilt dirt bike motors a carb motor for myself. I'm only a backyard mechanic... Haha

I will start going throught the service manual later this week.

Any thoughts ? Any thing else I am overlooking or that I should be paying attention to or replacing ?

Any comments are appreciated.

I’m looking into buys 14” wheels, what width are the factory wheels front and back? I want to try and keep the size differences and not go with the same tire size all around. Looking into putting Pitbull Growler XOR BG2.5 tires all around 27x9-14 on front and 27x11-14 on rear. What’s everyone else running wheel wise for this type of set up?

Secondly if you are running a similar set up how is the ride? 95% of the riding I do is trail riding. I’m open for any input and suggestions.

I’ve been searching through post trying to find what I’m looking for but haven’t really found it.

I got a 2006 sportsman 700 efi and I was plowing snow last night and all of a sudden it died on me. Still had power so I tried to restart but did not hear the fuel pump kick on. I had a previous issue with the relay to I cleaned out the connection and replaced and it had been running fine the past couple months. Could the pump have just gone out?