News

We have a 2017 outlander 1000 and I don't know were the fuse box is located. Can someone tell were it is and if it is hard to get. What do I need to do to get at it?
Thanks

I currently have have a 2015 maverick xds turbo. I have been eyeing up the x3 xrc 64” because the 72” is to wide for where I ride. I am bummed that it is only 120hp not the 172. The dealer keeps telling me it will be a huge improvement over mine. He said even tho it’s the same horsepower the triple cylinder and different clutching. It will be way more power than mine. Just tossing around the idea of maybe I should get a x3 turbo r or xds turbo r because they are 172hp.

First off- This is a new to me project, and appreciate all the help on this site.

Couple things electrical.
When turn key on and start it- the RED oil light is on always, drained oil, cleaned filter, new oil and its full.

R/N Lights- reverse and neutral I assume.
They never come on, I can move shifter and it goes in gear like it should but no lights.

Any advice- also has brand new battery..
Thanks Again...

Just purchased a 1000xmr on a bit of an impulse last night, has the big mudders which im not sure will work here for mostly trail riding and dirt roads.
I should have waited for the xrc but the dealer said nothing is coming in til spring and i got the bug to get something for the winter season here.

Any suggestions on what i should do?

Should i keep them and let them wear out: I may have to put some studs in the tires to make it up my icy hill.

Sell them as New and buy a different tires?

Should i keep them and get new rims and tires but that sounds way to expensive!

Just purchased a 1000xmr on a bit of an impulse last night, has the big mudders which im not sure will work here for mostly trail riding and dirt roads.
I should have waited for the xrc but the dealer said nothing is coming in til spring and i got the bug to get something for the winter season here.

Any suggestions on what i should do?

Should i keep them and let them wear out: I may have to put some studs in the tires to make it up my icy hill.

Sell them as New and buy a different tires?

Should i keep them and get new rims and tires but that sounds way to expensive!

This new to me project will fire right up if I put my hand over the intake boot (with air box off) for one second it has a lot of suction.
Gas will come into the boot and run. It still needs adjustment to idle well, but the first time it will just crank and not fire till I do that.
Rebuilt/cleaned carb, took pump apart, cleaned looked fine, new fuel, clean tank, petcock is working.
Tried to adjust the air screw under carb once, started at 2 1/2 out - then tried 1 1/2 out, did same thing.

What would cause this to fire only when I put hand over boot.
Once warmed up she will fire on her own.
Thanks in advance

Hello All
Wishing Everyone A Merry Christmas And All The Very Best In 2019

My question is ,does anyone know what a dealer download of my 2013 400HO will tell me.I don"t want to waste $$$ if it will not tell me whether my engine was over reved or overheated for prolonged periods of time.Loaned my machine out and when I got it back my motor had a loud knock coming from the upper front right side of the motor.I suspect they drove the hell out of my machine.It has 980 miles on it.Dealer is being very vague about the parameters of the download but wants $200.00 to do it.Any help will be Greatly Appreciated.
Thanks All

Hello trying to figure out why i have no power on my 01 sportsman 500 ho have battery in and turn key on and push the run switch over n no power lights don't like up nothing brand new battery brand new start and solenoid and brand new key switch. It does have a winch on it that was installed from the dealer when the first owner bought machine. But the winch should have nothing to do with it starting should it? The winch didn't work when i got machine i think the winch solenoid is bad. Is there any fuses or anything that would cause it to not have power i know if the hi low run switch unit is bad then that could be why but just wondering if there is anything else the hi beam switch was acting up like the hi beam would come on randomly or not come on at all the run switch though never acted up it was working fine now i get no power. Any help would be greatly appreciated.